Toyota Tundra Forum

woody, if my memory is not failing me, it seems to me that on the Gen 1's the truck trailer connector is above (and maybe slightly to the right of) the parking brake area, kinda' tucked in with some other wires.

__________________

2007 Tundra Limited Double Cab 4x4 Super White
Volant CAI
Pioneer AVIC Z-2 (hard drive upgrade to AVIC Z-3)
Key FOB Tailgate Lock (courtesy of Toxarch)
OEM back-up camera w/flip down monitor microswitch mod
Sirius Satellite Radio
WeatherTech Floor Liners
20" OEM alloy wheels
Line-X Bed liner
UWS Black Powdercoat Low Profile Toolbox
DU-HA underseat storage unit
JC Whitney Black Nerf Bars
Lund Interceptor II Bug Shield
Tekonsha Voyager Brake Controller

Cool, thanx, Ill give it another look see tonight and see what I come up with. Hopefully one day soon I will get the chance to upgrade to the Gen2 Tunrda. Even though I love mine, the newer body style is dang sexy!

You won't regret the upgrade woody, and there some deals to be made right now on the Gen 2 Tundras! BTW, good luck on your trailer brake controller.

If you find it, take a picture for the next guy.

__________________

2007 SR5 Crewmax 5.7L 4x4
Mods: nerf bars, Truxedo tonneau, radar detector power, 3M clear bra, fog lights, black billet grille, rear differential breather, parking sensors, Line-X, power tailgate lock, hood safety latch mod, one off driving lights behind grille, Pioneer NAV w/ OEM camera, Flowmaster 50 SUV dual/dual, blue LED dash lights, Volant CAI, Llumar tint, CompuStar Pro alarm, ProComp 6066 20" wheels, Cooper Zeon LTZ 275/60/20 tires, OME HD coilover lift, Firestone helper air bags, stereo cable lock, Tekonsha P3 brake controller
All mod descriptions and pictures © 2007-2009 by Toxarch. They may be copied only for personal use and the mods may be done for non-profit only.

I have an '05 access cab 4x4 & just got a 16x8 flat bed ATV hauler w/2 axles, single axle brakes. Got the truck used, look like factory tow pakage. Want install brake controller. HELP!!

See my post in the thread you started on this same subject.

can I drill a hole in the back of the pocket and fish the wire through to the side and kick panel. The toyota harness I got is to short to get to that pocket hole so I will have to extend it . The way the dash goes straight down so far it is hard to set that ps3 that far down to allow it to be horizontal.

__________________
2007 Tundra Crewmax TRD ,black, rhino bed ,magnaflows. 18" alloy, bars,extender, sirius 30% lumar,flaps,TRD sway bar, Ocean Deck Barstools (Daytona Beach) RJMETALWOODS.COM

Are you talking about the pocket below the A/C controls? I cut a rectangle hole in the back of the pocket for the plug. I used the harness that came with the truck, connected it to the harness that came with the P3 brake controller and added a new ground wire for it. It was more than long enough to reach from the truck plug to the brake controller. Prodigy was the one who recommended adding the ground wire. They said the Toyota ground in the plug was not large enough. I'm sure the pre-made harness you bought has the extra ground wire.

did you cut the hole from the front , with it in the dash or was it removed.
Thanks

I pulled the pocket out. Open up both cigarette lighter holes, put a thumb in each one, and pull. It will pop right out. Mark where the plug will hit the back of the pocket and use a dremel to cut the opening. If you don't have a dremel, you can drill the opening with a large drill bit and make 2 holes beside each other. I used a heavy duty 2" wide velcro to attach the controller to the top of the pocket. That velcro is pretty tough stuff and holds really well. Hasn't moved yet.